220-1101 domain - 15% of the exam

Mobile Devices

Mobile Devices is 15% of the 220-1101 exam. These are the objectives it covers, each with practice questions, with every answer explained.

The domain in numbers

45
Practice questions
4
Objectives
11
Easy
34
Medium

Where people go wrong

  • Placing an inverter in LED and OLED panels

    The wrong answers attach an inverter to the wrong display technology: an LED-backlit panel is said to need one, or to have a larger one, and an OLED panel is given inverters or a lamp. The inverter belongs to the CCFL tube, because it converts low-voltage DC into the high-voltage AC that lamp needs. White LEDs run from low-voltage DC, so an LED panel drops the inverter, and OLED pixels emit their own light with no backlight at all.

    See it in a sample question
  • Blaming the wrong layer for a touch or lighting fault

    The wrong answers pin a fault on a component that the symptom rules out. A sharp image with dead touch is sent to the LCD or backlight, and a dim but correctly rendered image is sent to the digitiser, the graphics processor or the crystal layer. The digitiser senses finger contact and reports coordinates, so it can fail while the picture stays perfect. A faint image visible under torchlight means the panel still renders, so the fault is in the backlight or its driver.

    See it in a sample question
  • Crediting TN with the strengths of IPS

    The wrong answers hand the wide viewing angles and accurate colour to TN, or give IPS the faster response and higher refresh rate. TN is the panel known for fast response, which tempts, but its colour shifts badly off-axis. IPS aligns the liquid crystals parallel to the glass, so colour and contrast stay stable at wide angles, which suits colour-critical work. VA improves contrast over TN but still trails IPS, and a CCFL backlight does not decide viewing angle.

    See it in a sample question
  • Ordering a memory module of the wrong form factor or generation

    The wrong answers offer a memory module that belongs somewhere else. Some quote a real pin count from another module: 288 pins is the desktop DDR4 DIMM, 240 pins a DDR3 desktop DIMM and 204 pins the DDR3 SODIMM. Others give the SODIMM more pins than a DIMM, or offer a DDR5 or DDR3 SODIMM for a DDR4 board. The DDR4 SODIMM has 260 pins, is shorter than a DIMM, lies flat in a horizontal laptop slot, and is keyed so another generation will not seat.

    See it in a sample question
  • Reading M.2 keying as a card's role

    The wrong answers misread what M.2 keying and length codes say about a card's job. Current laptop Wi-Fi cards use the A/E key in the compact 2230 length, which carries the PCIe and USB signals a radio needs, while the M-key 2280 slot is for NVMe storage. Keying governs physical fit only: a B+M keyed drive still seats in an M-only socket. A full-size PCI card or a soldered USB dongle is not how a current ultrabook takes its wireless card.

    See it in a sample question

Objectives in this domain

What to study

The official documents this domain's practice questions cite most.

Sample questions from this domain

Free sampleMobile Devicesmedium

In a laptop that uses a CCFL-backlit LCD, what is the specific function of the inverter board?

  • AIt converts incoming mains AC to low-voltage DC to charge the laptop's main battery.
  • BIt converts the system's low-voltage DC into the high-voltage AC needed to light the CCFL tube. Correct
  • CIt digitises touch input from the screen surface and passes coordinates to the operating system.
  • DIt regulates the DC voltage feeding an LED backlight strip along the bottom of the panel.
The inverter in a CCFL-backlit LCD converts low-voltage DC to the high-voltage AC required to illuminate the fluorescent backlight tube. A cold cathode fluorescent lamp ionises gas only under high-voltage alternating current, but a laptop supplies low-voltage DC, so the inverter board steps up and converts that DC into the AC waveform the lamp needs to glow.

Why A is wrong: That describes the external power adapter and charging circuit, not the display inverter, which drives the backlight rather than the battery.

Why B is correct: Correct: the cold cathode fluorescent lamp needs high-voltage AC, and the inverter steps up and converts the laptop's low DC supply to drive it.

Why C is wrong: Digitising touch is the job of the digitiser, a separate component; the inverter has nothing to do with touch input.

Why D is wrong: LED backlights run on DC and do not use an inverter, so this is tempting but describes an LED panel, not a CCFL one.

Free sampleMobile Devicesmedium

Tom's tablet displays a bright, sharp, correctly rendered image, but the touchscreen no longer responds to taps or swipes anywhere on the surface, and the glass is not visibly cracked. A reboot does not help. Which display-assembly component is the most likely fault?

  • AThe LCD panel, because a faulty panel loses its touch grid and stops registering input even though it can still show a picture.
  • BThe digitiser, because it is the touch-sensing layer that converts finger contact into input, and a failed digitiser stops touch while the image keeps rendering. Correct
  • CThe backlight, because without backlight power the touch layer loses the voltage it needs to register taps across the surface.
  • DThe inverter, because it powers the capacitive sensing grid and a failed inverter leaves the screen visible but unresponsive to touch.
Attribute a perfect image with fully unresponsive touch to the digitiser, the layer that senses contact separately from the display. A capacitive digitiser is a distinct layer that senses the change in an electrostatic field when a finger touches the glass and reports coordinates to the system; because it is separate from the image-forming LCD and its backlight, it can fail completely while the display continues to render normally.

Why A is wrong: The LCD renders the image and does not contain the touch sensor, so a working picture actually rules it out; this conflates the display layer with the separate digitiser.

Why B is correct: The digitiser detects touch independently of the display, so it can fail while the picture stays perfect; an unresponsive screen with a clean image is the textbook digitiser symptom.

Why C is wrong: The backlight only illuminates the panel and shares no circuit with touch sensing; a bright image proves it is working, so it cannot explain dead touch.

Why D is wrong: Inverters drive CCFL backlights, not touch grids, so this misassigns the digitiser's job to an unrelated and mostly legacy component.

Free sampleMobile Devicesmedium

Priya is a photo retoucher who often has a colleague lean in over her shoulder to review edits on her laptop. She reports that colours look accurate to her but shift and wash out when viewed from the side. She wants a replacement panel that keeps colour consistent across wide viewing angles. Which LCD panel type should the technician specify?

  • AA TN panel, because twisted nematic technology offers the fastest pixel response and therefore the most accurate colour reproduction at any viewing angle.
  • BAn IPS panel, because in-plane switching aligns the liquid crystals parallel to the glass so colour and contrast stay stable across wide viewing angles. Correct
  • CA CCFL-backlit panel, because a cold cathode fluorescent backlight widens the effective viewing angle and improves off-axis colour fidelity.
  • DA standard TN panel fitted with an anti-glare digitiser, because the matte digitiser layer corrects the colour shift seen from the side.
Recognise that IPS panels trade some response speed for stable colour and wide viewing angles, making them the choice for colour-critical work. IPS switches the liquid crystals within the plane of the glass rather than twisting them perpendicular to it, so light output stays consistent as the viewing angle changes, which keeps colour and contrast accurate off-axis where TN panels shift and invert.

Why A is wrong: TN does have fast response, which tempts gamers, but it has the narrowest viewing angles and the weakest colour accuracy, so it fails Priya's requirement.

Why B is correct: IPS aligns crystals parallel to the panel, which preserves colour accuracy and contrast off-axis, matching both the colour-critical work and the wide-angle requirement.

Why C is wrong: Backlight type sets brightness and power draw, not viewing angle; CCFL is an ageing backlight technology and does nothing to correct off-axis colour shift.

Why D is wrong: A digitiser handles touch input, not image rendering, and an anti-glare finish reduces reflections rather than fixing the underlying TN off-axis colour problem.

Free sampleMobile Devicesmedium

A technician is ordering replacement memory for a laptop that uses DDR4 SODIMM modules. How many pins does a standard DDR4 SODIMM have?

  • A260 pins, the standard edge-connector count used by DDR4 laptop memory modules Correct
  • B204 pins, the standard edge-connector count used by DDR3 laptop memory modules
  • C240 pins, the standard edge-connector count used by DDR3 desktop memory modules
  • D288 pins, the standard edge-connector count used by DDR4 desktop memory modules
Recognise that a DDR4 SODIMM uses 260 pins, distinguishing it from DDR3 SODIMMs and from desktop DIMM pin counts. SODIMMs are the compact memory form factor used in laptops, and JEDEC assigns each generation a distinct pin count so incompatible modules cannot seat; DDR4 SODIMM is standardised at 260 pins while DDR3 SODIMM is 204.

Why A is correct: Correct: JEDEC defines the DDR4 SODIMM with a 260-pin edge connector, distinct from the DDR3 SODIMM and from desktop DIMMs.

Why B is wrong: Tempting because 204 is a genuine SODIMM pin count, but it belongs to DDR3 SODIMM, not DDR4, so it is the wrong generation.

Why C is wrong: Tempting as a real DDR3 pin count, but 240 pins is a full-size desktop DIMM, not the smaller laptop SODIMM form factor.

Why D is wrong: Tempting because 288 is the correct DDR4 count, but it applies to the full-size desktop DIMM, not the laptop SODIMM.

Free sampleMobile Devicesmedium

Daniel installs a 1 TB M.2 drive keyed M into a laptop and the system does not detect it, although the same drive works in an external NVMe enclosure. Which mismatch is the most likely cause?

  • AThe drive is an M.2 NVMe device but the laptop's M.2 socket only supports M.2 SATA modules Correct
  • BThe drive uses a B+M key so it is physically blocked from entering the M-keyed socket
  • CThe 1 TB capacity exceeds the addressable limit of the laptop's M.2 storage controller
  • DThe module is a wireless card in an M.2 2230 length rather than a storage drive
An M.2 slot that fits a drive may still support only SATA or only NVMe, so protocol support must match the module. M.2 keying controls physical fit but not logical protocol. A socket keyed M can be provisioned for SATA only; an NVMe module inserted there fits mechanically yet is never enumerated because the host lacks the PCIe lanes the drive needs.

Why A is correct: An M-keyed slot can be wired for SATA only, NVMe only, or both. A SATA-only socket will not initialise an NVMe drive even though the connector fits, which matches a drive that works in an NVMe enclosure but not here.

Why B is wrong: A B+M keyed drive actually fits an M-only socket, and the stem says it seated, so keying is not the blocker. It is tempting because keying does govern fit in other cases.

Why C is wrong: A 1 TB module is well within normal M.2 capacities, so a capacity ceiling is not credible. It tempts candidates who recall legacy drive-size limits from older BIOS systems.

Why D is wrong: Wireless cards use A/E keying and would not appear as a 1 TB drive that works in an NVMe enclosure. It plays on M.2 hosting both roles, but the described device is clearly storage.

Other domains in this exam

See also the 220-1101 cert hub, the study guide, and the cheat sheet.

Examworthy is not affiliated with or endorsed by CompTIA. Original, blueprint-aligned practice material only.